Linear ACCESS AE-100 Manual de usuario Pagina 17
- Pagina / 24
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
17
FUNCTION CODE LOCAL PROGRAMMING TELEPHONE PROGRAMMING
05
MANUAL ACCESS
RELAY CONTROL
This command can be used to
latch the access relay indefi nitely
or for a period of time, and to
unlatch the access relay.
Step 1 Enter Function Code 05, then press #.
Step 2 Enter the number of hours from 01-98 to
energize the access relay, then press #.
- OR -
Enter the 99 to energize the access
relay indefi nitely, then press #.
- OR -
Enter the 00 to de-energize the
access relay, then press #.
- OR -
Enter ✱ to cancel this command.
Step 1 Enter Function Code 05 and
press #, one short beep sounds.
Step 2 Enter the number of hours from 01-98 to
energize the access relay, then press #.
- OR -
Enter the 99 to energize the access
relay indefi nitely, then press #.
- OR -
Enter the 00 to de-energize the
access relay, then press #.
Two long beeps and two
short beeps will sound.
06
DIRECTORY CODE
LENGTH
Selects 2 or 3 digits for the
Directory Code length (factory
default is 3 digits).
NOTE: In multi-unit installations, if
sub-units are being updated with
access data that has Directory
Codes with more digits than the
sub-unit is set for, the sub-unit’s
Directory Code length number will
be automatically adjusted to fi t.
Step 1 Enter Function Code 06, then press #.
Step 2 The display shows the current value.
Enter 2 or 3, then press #.
- OR -
Enter ✱ to cancel this command.
NOT AVAILABLE
10
WELCOME DISPLAY
TEXT
The AE-100 display will show
a visitor a welcome message
alternating with instructions on
how to fi nd and call a resident.
The welcome message can be
customized to suit the installation.
Step 1 Enter Function Code 10, then press #.
Step 2 Enter the new welcome message. A total of 32
characters are allowed. The display will advance
to the lower line after the 16th character is
entered on the upper line. Enter # after each
character, enter ## after the last character.
NOT AVAILABLE
30
COPY ACCESS
DATA ONLY FROM
MASTER TO
SUB-UNITS
To synchronize programming
in multi-unit installations, the
Directory Entries and Stand-alone
Entry Codes can copied from the
master unit to selected sub-units.
CAUTION: This utility
command will overwrite ALL the
access data in the sub-unit(s)
selected.
Step 1 Enter Function Code 30, then press #.
Step 2 Enter the number(s) (2, 3, and/or 4) of all the
sub-units to copy the data to, then press #.
Step 3 Enter 5 for verifi cation, then press #.
- OR -
Enter ✱ to cancel this command.
NOTE: The installer must setup the system as a multi-unit
installation before this command will operate.
Step 1 Enter Function Code 30 and
press #, one short beep sounds.
Step 2 Enter the number(s) (2, 3, and/or 4)
of all the sub-units to copy the data to,
then press #, one short beep sounds.
Step 3 Enter 5 for verifi cation, then press #,
two short beeps sound. (Any entry other
than 5# will cancel the command.)
NOTE: To allow for multi-unit network
communications, when executing this
command remotely over the telephone,
the system will disconnect your call
after Step #3 then copy the data from
the master unit to the sub-units.
O P E N : 0 0 H O U R S
D I R D I G I T S : 3
( B L A N K D I S P L A Y )
U N I T S :
A R E Y O U S U R E ? 5
ALTERNATE PROGRAMMING METHOD
- Commercial 1
- Telephone Entry 1
- System Features 3
- Access to Programming 4
- Connecting with a Telephone 5
- Telephone Audio Prompts 5
- Exiting Programming Mode 5
- Multi-unit Installations 6
- 23#DIR#DIR# 7
- 33#CODE#CODE# 8
- 31#CODE#CODE# 8
- 51#COUNT# 9
- 61#ANSWER# 10
- 62#CHIRP# 10
- 64#TIME# 11
- 30#SUB-UNITS#5# 12
- 34#SUB-UNITS#5# 12
- 80#HOURS# 13
- ALTERNATE PROGRAMMING METHOD 14
- AE-100 Operation 22
- Troubleshooting 23
Seed-hawk AIRCART 2014 manuály
Uživatelské manuály a uživatelské příručky pro Zahradnické vybavení Seed-hawk AIRCART 2014.
Poskytujeme 1 manuály pdf Seed-hawk AIRCART 2014 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentarios a estos manuales